These are step by step instructions to build a poker table. The table measures 48 "x 96" and have a 4 "rail width. This will provide enough space for 10 players.
These instructions for use pine boards for the legs and frame, because they are painted. If you prefer to paint the table, you might want to replace other types of wood. It is advisable to buy folding table legs, the legs on your use> Table.
End Table Wood
Materials needed:
3 - 4'x8 'sheet ¾ "MDF
10-8 '1 x4 Select Pine Boards
1 to 6 "1x10 Pine Select Board
4 - Black Strap Hinges
4 - Table Greaves
Quality Wood Glue
1 can - 3M Hi-Strength 90 spray adhesive (green box)
Qt before paint (black)
Qt first polyurethane
8-2 "bolts with nuts Tea
1 - Box 1 ¼ "drywall screws Black
16-4 "drywall screws Black
Wood Filler
¼ " Closed cell foam 96 "x48"
22 1 "thick foam Rail - 3 # force
Vinyl 55 "x 108"
Tablecloth 55 "x 108"
Optional - 2 folding banquet table legs (7-8 '1 x4 removing pine boards Select)
Tools needed:
Jig Saw
Made with knife
Belt sander with 120 sandpaper
Orbital sander with 180 sandpaper
Router
Drill ¼ "round-over with the series"
Drill
Drills (3 / 4 "Spade, 1 / 8" wood ¼ "> Wood, 5 / 16 "wood)
Sink
Terminals
Utility Knife
Hammer
Staple gun
Staples
Brush or spray
Phase 1 - Table Top layout and rail pieces
Draw your table / rail track 3 pieces of MDF. The plan is unique and the guide is composed of 3 parts (upper, middle and bottom).
The first sheet 48 "x 96" MDF
The first sheet produces the bottom of the guide and the tablehigher.
Locate the line 24 "at the end and 24" on the side; brand. Do the same at the other end. These are the points that will produce beams for semicircles.
The first semi-circles on the outer edge of the bottom rail pieces. Measure 24 "from the marked locations (this will be at the edge of the MDF). Draw a semicircle from one side of the sheet of MDF on the other, creating a semicircle. Repeat on other side.
The secondSemicircle to the inner edge of the bottom rail pieces. Measure 22 ½ "from the marked point. Draw a semicircle on both ends. Now, connect a straight line along both sides of the two semicircles.
The third semi-circle around the table for the piece. Measure 22 ¼ "from the marked point. Draw a semicircle on both ends. Now, connect a straight line along both sides of the two semicircles.
Sheets, second and third 48 "x 96"MDF
These panels produce the middle and top of rail.
Again, the point 24 "at the end and 24" which is on the page, Mark. Do the same at the other end.
Measure 24 "from the marked point and draw a semicircle. Repeat other side. This has created the outer edges of the guide.
Measure 20 "from the marked point and draw a semicircle. Repeat other side. This has created the inner edges of the guide.
This is a4 "rail width.
Step 2 - Cut the top of the table and rail pieces
Use a jigsaw to cut 4 pieces of MDF. Do your best to get a nice cut, even along the lines. First you cut corners. Then, a pilot hole for jigsaw blade. Use a "peak ¼. Drill the hole next to the line, not in it (even in pieces of table or rail). After the holes are drilled and then cut the remaining pieces.
Step 3 - InstallationRail sections
The next step is to be mounted on the guide. These pieces are glued and screwed together. Dry fit the three pieces together to see which way they fit better.
This Piece Set-Top and Middle
First, wood glue on one side of the top. So, at the center on the head. Make sure they are fed together. Clamp together. Use a "point and holes every 8" 1 / 8 - 12 "around the track with a countersink on the hole, then.The bolt will be sunk into the wood. Screw 1 ¼ "drywall screws into the holes. Remove parentheses.
Bottom-up mounting units / Middle-Pieces
Glue on one side of the bottom piece. Place the bottom of the other pieces. Make sure the pieces together until fed. Clamp pieces. Use a 1 / 8 "tip and holes every 8" -. 12 "around the track with a countersink the hole so the screw can be inserted into the screw wood 1¼ "drywall screws into the holes. Remove parentheses. Fill each of the holes with wood putty. Let the wood putty to dry.
Step 4 - Guides and milling table
- Table Top -
Sand to remove the top of the table of bumps or bruises to be cut with a belt sander.
Rail -
All edges of the rails must be rounded. This can be done with a belt sander, but work, preferably with a router.With a ¼ "round-over stock" cutter works great. Each of the five edges must be rounded.
Use the belt sander to sand on the side of the guide. Try as smooth as possible. Use the orbital sander to sand the top and slightly rounded edges again. Make sure that the wood filler, sanded smooth.
Step 5 - Table Top and Rail Seal
Apply a thin layer of polyurethane, and the top edge of the floor, and from all sidesthe railroad. Together these pieces aside and let them dry. This means two things, protects the wood from spilled drinks, and especially the stick spray helps better.
Step 6 - basic table
Cut Pieces-frame -
They will cut a total of 7 pieces for the frame. Use 3 of the 8 x 4 x 10 1 6 '1 '1Cards for the frame. Use one of the 1x4 boards, cut 2 to 31 July / 8 "long pieces, and March 1 to 30 / 8" long pieces. Then cut 2-64 "long pieces, one from each of the two remaining cards, 1x4 finely chopped 2 -. 30 8.3" long pieces from the 1x10 board.
Fit-frame-Pieces
At either end of the tail, flaring two pilot holes. The side panels are neck and neck until the end pieces. Wood glue on the ends of side pieces. Assemble the front and side wallsThe pieces together. Use 8 -. 1 ½ "drywall screws to hold together this is a rectangular frame.
At half-time (32 ¾ "), who is now 65 ½" side, drill countersunk pilot holes 4, two holes on each side. Glue the ends of its support center 30 8.3 1x4. Insert it into the frame and secure it with 4 to 1 ½ "bolts.
The 2 -. 30 8.3 "1x10 leg mounting plates go to the next, these plates are flush with the topEdge of the frame. Countersink drill 10 holes on each side, mounted on board, 3 and 4 holes on each side at the end of glue on three sides of the leg on board .. Plug it into the frame and secure it. Fill all screw holes with putty.
Step 7 - Attach Table Top Frame
If the table lying on the bottom. Place the frame on top of the table. Make sure the frame is centered in both directionson top. Use a pencil to draw the frame on the table. Overview of both inside and outside of the chassis, including support to the center and mounted to the leg.
Remove frame from above. Use a 1 / 8 "bit and drill holes every 4" -6 "were all around the structure to be. Will drill holes for the legs increases. Flip over the top and bottom are each of these holes.
Turn over the top of the back. Wood glue to the top of the frames were attached. Place the new framehigher. Start the mounting screws on the bottom. Make sure that the corners are set, and you can turn around and finish most of the screws from the top. It 'a little' easier. Remove excess glue.
Step 8 - table legs
Rough-Cut Leg Pieces -
Cut of 15 to 27 "pieces of 1x4 cards '1 x4 5 8 -. 16 Cut 27" piece from one of the left over 32 "Pieces of the frame. These 16 panels will be the four legs.
Cut 8 to 24 "pieces from the remaining 2 -. 8 '1 x4 card This eight boards, two bars for the legs.
Glue-Leg Pieces -
Divide the 16 -... 27 "sheets of 4 legs in 4 groups of 4 cards with glue and clamp together Repeat for the other three legs, let the glue before you put in brackets.
Divide the 8-24 "support cards in 2 groups of 4 Glue the 4 plates and lock it.together. Repeat for the other medium. Let the glue before you put in brackets.
Loop Leg Pieces -
Use a belt sander and sand and pieces of legs smooth. Just sand the common side of these pieces. Then, use the router with the ¼ "round-over with the series" bit and round the corners of the legs and support pieces. Use the orbital sander to sand the pieces of beautiful smooth surface.
Fine Cut Leg Pieces -
Ready to cut each leg 26 ½ ". CutFrom a portion of each end of each phase to ensure that both ends of the leg have a cut over. Sand with the orbital sander.
Ready to support any cut 23 ¾ ". Cut a piece at each end of each support, to ensure that both ends of the carrier have a cut over. A golden sand with the orbital sander.
Saddle-Fit -
The four legs is 3 "x 3 ½" wide. Lay the 4 legs side by side with the 3 ½ "at the top. Sizethe bottom of each leg, 5 "and 8 ½". Mark these measurements on each leg. This is the place were the cross supports, attach the legs.
Drill four 3 / 16 "holes completely if each leg. Use a countersink or 3 / 8" tip and a ½ "to ¾" deep hole cut for each of the 16 holes. Wood glue to both ends of each support pieces. Insert the screws into the holes and fasten the legs to support them in this. Do this for each Leg.
Remove excess glue. Fill the holes of the screws with wood filler. Once the glue and plaster is dry, sand smooth these areas with the sander.
Step 9 - Painting
This painting, chassis legs and the bottom of the table. Enter the color that is an increasingly easy for you, paint spray, brush or spray. First, a primer. You need to make two layers. The drying time between coats.
Step 10 - Install legs> Table
Setting the table with the flat bottom. Insert the legs into their positions. Keep your legs firmly against the frame at the ends, leaving equal space between the legs and sides. Install the hinges and the table leg braces. Go back to the table and stand with your legs down.
Step 11 - Installation of T-Bolt nuts in the guide
Position the track position on the table. Under the table to ensure There is still a gap between the table and rail. This gap is necessary for the felt and vinyl. Once the train is positioned correctly, secure it firmly.
They are evenly spaced holes 8 holes around the track, these holes should be 1 8.1 "from the inside edge of the rail with a ¾". Punta spade drill holes with a depth of 8 ½ "- ¾". Using a "5 / 16 wood drill bit, drill through the remaining depth of the guide and through the> Table.
Take the train from the table. Gently pound each of the dowels into the holes. Put a ¾ "piece of plank back support below the edge of the rail, so that the rail is not damaged. Fixed rail on the table, screwing it in place with all eight bolts. Fill in the ¾" holes with wood putty. Sand when dry.
Step 12 - Foam
Both the board and the guidance necessary to apply the foam on it.
- Table-
Spray the top of the table with the adhesive. Place the "closed cell foam ¼ on the table. Press the foam in the center and working to resolve the edge off. Ensure that all air bubbles.
Locate the holes for the ', rail bolts and cut open.
Rail -
Glue the foam on the top rail to rail. Make sure you have enough foam hanging over the edge of the sides of the track meet.
Depart from a central point of one of the straight sides. Working in twoFoot at a time. Spray adhesive on the top rail. Put just sprayed foam on the surface of glue. Once you have joined the railway job for the next two foot section. Put this all the way around. When you get all the way around to overlap the foam and cut with a razor knife to the joint. Then glue down the last section, making sure that the ends close to each other.
Next, you glue the sides down and also wrap around the bottom of the rail. Then cut the excess with a knife.
Step 13 - Table Felt
Place the felt on the table with much more hanging on the sides. Use a gun to secure the base was on the table. You will be stapling the felt on the edge of the table.
Start at the center of the long sides. Placed in 1 of the base. On the other hand and pull you feel tense. To put a full stop in one, the round ends. Tighten the feeling Jump and put 1 point to another> End and pull it tight and put 1 point in going half-way between two of the staples and pull it tight and put in a bow. Then go to the other side and repeat. Continue until the entire piece of felt is tight and in place. "- 4" Staples should be 3 pieces.
Use a utility knife and cut all the excess felt. Cut with the lower surface of the table. Gently with a hammer to hit all the points that are not fully
Locate the holes for the guide screwsand cut open.
Step 14 - Rail Vinyl
This can be a difficult part of the job, especially when working with vinyl, does not stretch very well. The vinyl covers that we have for sale at this point is very nice to do this part a little 'easier.
Place the flat vinyl with the black side down. Put the track on vinyl, from top to bottom. Make sure the rail is at the center of the vinyl. The vinyl is completely cover every surface of the rail. The seam will be located atInside corner on the underside of the rail.
Start in the middle of a late shift. Lift the vinyl and the inside edge, and instead put a staple food. On the other side and do the same. Take the utility knife and cut the vinyl in the middle of the inner rail. The cut of about 5 'in length parallel to the straight sides of the guide. (The reason for this is that you pull the vinyl on the sides and then will go around the turnends.)
Pull the vinyl in the middle of one side, the intersection that you put in the middle begins to attract about 3 open. "Then put a full stop on the inner edge. Repeat other side. The middle section should be about 6" wide in the middle.
They will make the outer edge of the pages, even before. Working on yourself down the first bracket, where the railway begins round. Gently pulling the vinyl up and over and attach to the inside edge. Then work the other Direction from the center and then to the other side.
Once the vinyl is wrapped around the outside and sewn in place, take the knife and run it to remove the bottom inside edge of the track and all the excess vinyl. Gently with a hammer to hit all the points that are not fully
It 'time to wrap the inside of the straight sides. Use the utility knife and cut the ends of the existing intersection, right on each page and three sections in the direction of the roundabout> End of guidance, the preparation of 4 triangular pieces. Cut until they are about 4 "from the guide. Now take the side panels of vinyl and pull it tight and staple it in place. Start in the middle and then work in any direction. Run knife to remove the inside bottom edge and any Excess vinyl.
Then wrap the inside of the turn ends. Cut two triangular pieces in half, so by 8 triangular pieces. Start on one side and take the first piece and pull it tight and staple it in place. Continueat the end of the track stitching each piece in its place. Repeat on the other side and cut the excess vinyl.
The exterior of the round is over, is the most difficult part of the vinyl. You have to be more and stretch vinyl and attach the railing. The end of the runway is already stitched vinyl. Beginning in the mid-way between the end and the side. Then drive halfway between the fixed points, until it veered all right. The trick is not to lookwrinkle-free vinyl. Once you have attached both ends in place, then cut protruding vinyl. If the holes for the screws, rail and cut open.
Step 15 - Think Place
Insert the rails instead of on the table. Put a washer for each bolt. Drag each of the bolts through the bottom of the table in the bar.
How to make a poker table